Frigidaire oven error codes are F codes such as F10, F30 and F90 that point to a problem with temperature, a sensor, the controls or the door lock. Frigidaire's first fix for most of them is a power reset: disconnect power to the range for about 30 seconds, then restore it. Find your code below to see what it means and what to do next.
Quick Answer: How to Clear a Frigidaire Oven Error Code
- Turn the oven off and, for F10, let it cool completely.
- Disconnect power for 30 seconds: unplug the range or switch off its breaker, then restore power.
- Try the oven again. Frigidaire says a power reset clears most false error codes.
- If the code returns: if the range was installed in the last 30 days, contact your installer; otherwise, schedule Frigidaire service.
Frigidaire Error Codes by Severity
Our guide to how urgent each of the Frigidaire range error codes is, based on what Frigidaire says it means.
Stop and act now
F10 Thermal runaway: the oven is detecting higher-than-normal temperatures. Turn it off and let it cool.
Reset, then service if it returns
F30, F31 open or shorted probe · F1 shorted keypad · F3, F20, F26 communication error · F12, F13 control errors · F90–F94 door lock issue
Usually not a fault
– (dash) or lock messages: the cooktop or controls are locked · F40, F41 cooktop lockout · Demo mode
How to Reset a Frigidaire Oven
- Turn the oven off at the controls. For F10, wait until it has fully cooled.
- Disconnect power: unplug the range, or switch off its circuit breaker. Frigidaire notes a breaker reset also resets anything else on that circuit.
- Wait about 30 seconds.
- Restore power, set the clock if needed and try the oven again.
- If the code returns, stop using the oven and arrange service.
If the reset happened after a storm or outage, see how to reset an oven after a power outage.
Frigidaire Oven Error Codes Explained
Thermal Runaway (Oven Too Hot)
UrgentFrigidaire says: on standard range ovens and wall ovens, F10 means the oven is detecting higher-than-normal temperatures, a built-in safety alert. Turn the oven off and let it cool before using it again. On Frigidaire's stone-baked pizza ovens, F10 can be caused by the Pizza Shield being in the wrong rack position; Frigidaire says to confirm it's in rack position 7 (some models vary) and restart the pizza preheat.
What it usually involves: in general appliance repair, a runaway temperature points to the oven temperature sensor, a stuck relay on the control board, or an element that stays on.
What to do: turn it off, let it cool, reset power for 30 seconds and test. If F10 returns or the oven keeps heating when off, switch off the breaker and call for service. Don't leave it running unattended.
Open Probe or Shorted Probe
Reset, then serviceFrigidaire says: F30 is an "open probe" and F31 a "shorted probe" on electric ranges and cooktops. Frigidaire's fix for F30 is to disconnect power for up to 30 seconds by unplugging the range or flipping the breaker.
What it usually involves: on ranges, "probe" generally refers to the oven temperature sensor (the thin rod inside the oven, usually at the back). An open or shorted reading often means the sensor, its connector or the wiring has failed.
What to do: reset power. If the code returns, the sensor or wiring needs testing. If you use a meat probe, unplug it and see whether the code clears. For uneven or wrong temperatures, our guide on testing oven temperature helps confirm the problem.
Door Lock Issue
Reset, then serviceFrigidaire says: these codes indicate a door lock issue. To unlock the oven door, press the UNLOCK key and follow the on-screen directions. Disconnecting power for up to 30 seconds clears most false error codes.
What it usually involves: the lock motor, its switch or wiring, often noticed after a self-clean cycle.
What to do: let the oven cool, try UNLOCK, then reset power. Never force a locked door. If it stays locked or the code returns, schedule service. Our guide to the self-cleaning cycle explains why doors lock.
Shorted Keypad
Reset, then serviceFrigidaire lists: F1 as a shorted keypad on its electric range code guide.
What it usually involves: a stuck or damaged touch key, moisture on the control panel, or a fault in the keypad's ribbon cable.
What to do: make sure the panel is clean and dry, then reset power. If F1 returns, the keypad or control needs service.
Communication Error
Reset, then serviceFrigidaire lists: F3, F20 and F26 as communication errors.
What it usually involves: the control boards or display not communicating, often from a loose connector, a power surge or a failing board.
What to do: reset power for 30 seconds. If the code returns, especially after a storm, call for service.
Control Errors (Micro Identification, E Prompt Failure)
Reset, then serviceFrigidaire lists: F12 as "micro identification" and F13 as "E prompt failure." These are internal control-board errors.
What to do: reset power. If either code returns, the control board needs service; these aren't user-fixable.
| Code | Frigidaire meaning | First step |
|---|---|---|
| F1 | Shorted keypad | Dry panel, reset power |
| F3, F20, F26 | Communication error | Reset power |
| F10 | Thermal runaway | Turn off, cool, reset |
| F12 | Micro identification | Reset power |
| F13 | E prompt failure | Reset power |
| F30 | Open probe | Reset power for 30 seconds |
| F31 | Shorted probe | Reset power |
| F40, F41 | Cooktop lockout | Unlock cooktop; reset if needed |
| F90–F94 | Door lock issue | Press UNLOCK; reset power |
Lock and Dash Messages
- A dash (–) on the display: Frigidaire says this means the cooktop is locked. To cancel the lock, press OFF and hold for 6 seconds; the control will unlock and resume normal operation.
- F40, F41 (cooktop lockout): the cooktop is locked out. Turn off the lock feature per your manual, then reset power if it doesn't clear.
- Demo mode: if the display lights but nothing heats, the range may be in demo mode. Frigidaire's steps: turn off the breaker, wait 45 seconds, turn it back on, then turn off demo mode in the settings menu.
Not sure what an icon on your control panel means? See our oven symbols guide.
Error Codes on a Newly Installed Range
Frigidaire advises that if the range was installed within the past 30 days, you should contact your installer first, because codes on new installs are often caused by wiring, power supply or installation issues. After 30 days, contact Frigidaire to schedule service.
- Confirm the range is on the correct dedicated circuit and both breaker halves are on.
- Check that the power cord or hard-wire connection matches the installation guide.
- Make sure no packing material or accessories are blocking the door lock or fan.
DIY or Call for Service?
Safe to try yourself
- 30-second power reset
- Letting the oven cool (F10)
- Pressing UNLOCK (F90–F94)
- Drying and cleaning the control panel
- Turning off lock or demo mode
Call a technician for
- Any code that returns after a reset
- An oven that keeps heating when off
- Replacing sensors, lock motors, keypads or boards
- Burning smells, sparks or a gas smell
- A door that stays locked when cool
Have your model and serial number ready (usually on a label inside the door frame or storage drawer). If repairs are adding up on an older range, see how long ovens last.
How to Prevent Frigidaire Error Codes
- Keep the control panel dry; spray cleaner onto a cloth, not the panel.
- Use self-clean sparingly; extreme heat stresses the lock and sensors.
- Keep the oven sensor clear of foil and pans so it reads correctly.
- Switch off the breaker during storms and long outages to protect the electronics.
- Check temperature yearly with an oven thermometer to catch sensor drift early.
Other symptoms without a code? Start with our oven troubleshooting guide.
Frigidaire Oven Error Code FAQs
How do I reset my Frigidaire oven error code?
Turn the oven off, then disconnect power for about 30 seconds by unplugging it or switching off the breaker. Restore power and try again.
What does F10 mean on a Frigidaire oven?
F10 is a thermal runaway alert: the oven is detecting higher-than-normal temperatures. Turn it off and let it cool. On stone-baked pizza ovens, check that the Pizza Shield is in the correct rack position.
What does F30 mean on a Frigidaire range?
F30 means "open probe." Frigidaire says to disconnect power for up to 30 seconds; if it returns, the temperature sensor or wiring likely needs service.
What does F90 mean on a Frigidaire oven?
F90 through F94 indicate a door lock issue. Press UNLOCK and follow the screen, then reset power if needed.
What does F1 mean on a Frigidaire oven?
F1 is listed as a shorted keypad. Dry the control panel and reset power; if it returns, the keypad needs service.
What does a dash on my Frigidaire display mean?
The cooktop is locked. Press OFF and hold for 6 seconds to unlock it.
Why is my Frigidaire oven not heating but showing no error?
It may be in demo mode. Turn off the breaker for 45 seconds, restore power and turn off demo mode in the settings. Also check both breaker halves.
Is it safe to use my oven with an F10 code?
No. F10 means the oven is too hot. Turn it off and let it cool; if the code returns, switch off the breaker and call for service.
My range is new and shows an error. What should I do?
Frigidaire says to contact your installer if the range was installed in the last 30 days, since wiring or installation is a common cause.
Where do I find my Frigidaire model number?
Usually on a label inside the oven door frame or the storage drawer.
The Bottom Line
Most Frigidaire oven error codes clear with a 30-second power reset. Treat F10 seriously: turn the oven off and let it cool. For F30, F31, door lock codes and control errors, reset first, then schedule service if the code comes back. New installs should go back to the installer first.
About this guide
Written by the TopOvenPicks editorial team using Frigidaire's official owner support articles. Where Frigidaire only names a code, we explain what it usually involves based on general appliance repair knowledge. Always check your Use and Care Guide.
Sources: Frigidaire Ranges Error Code Guide · Oven Error Codes and Alarms Guide
TopOvenPicks is reader-supported. When you buy through links on our site, we may earn an affiliate commission at no extra cost to you. Prices and availability change often, so always confirm details on Amazon.





